The last chord of your song would sound right in the stairwell where you first wrote it. Take a dry recording back there on paper first. Mark where the player stood and where a listener heard the decay. Then make two mono files from those positions: a clap for a quick creative effect and a measured impulse response for repeatable use. A convolution reverb can apply the timing and tone in either file to a new sound. The file captures a particular path through the space, so moving the source or mic gives a different result. Apple’s explanation of impulse responses and deconvolution
Enlarge diagram
Mark a source and a receiver
Use a space where you can make sound without disturbing anyone or blocking a passage. For example, put the source 1.2 m above the floor and the microphone 2 m away at the same height. Note each position relative to a fixed wall, whether the door is open and which way the mic faces. Keep the mic stationary throughout. Record at a single rate such as 48 kHz and capture a few seconds of background. It will help you recognise where the decay becomes indistinguishable from the room noise.
For the sweep, use one loudspeaker at the marked source and one mic at the receiver. Select the physical mic input and speaker output. Disable microphone return to the speaker in the software and interface mixer. Start at low playback level. Your mic and loudspeaker each contribute their own frequency response. An ordinary recording mic and small speaker can supply a useful musical effect, with limited information where either device has little output. Apple’s impulse-response recording setup · Room EQ Wizard’s setup guide
Make the clap version
From the source mark, clap once with your hands at the intended source height. Wait through the decay. Make three separate takes, keeping the gain fixed after a short level test. Listen for a clean attack followed by reflections. Reject any clipped take, overlapping footsteps or take with a second clap inside the tail. On a copy of your favourite file, trim the lead-in to just before the onset, preserve the natural decay, and fade the end where it merges into room noise. Leave the raw recordings intact.
Load that edit into a convolution reverb and send a dry rimshot to it. The handclap has its own spectrum and finite duration. A hollow palm sound or double attack can become part of every processed hit. A clap gives a musical comparison of positions, but its spectral gaps prevent an accurate full-band measurement. Apple’s transient and swept recording methods
Measure with a known sweep
- In Room EQ Wizard (REW), choose Measure and its acoustic SPL measurement mode. Select the intended output and mic input. Set the sweep range inside the loudspeaker’s supported range. For example, try 100 Hz–12 kHz on a compatible small monitor. Any result outside the chosen band has limited meaning.
- Try one 256k logarithmic sweep at 48 kHz. Its 262,144 samples take roughly 5.46 seconds. Use Check Levels at a comfortable playback level, check the input for clipping and leave the room quiet through the measurement. Keep the source, mic and gain settings fixed during a second pass. REW’s measurement controls
- Inspect the Impulse view. REW derives the IR from the measured response to its known sweep. Deconvolution removes the excitation signal from the calculation, leaving the estimated response of the playback, room and capture path. The raw sweep recording itself will produce a rising pitch if mistakenly loaded as the reverb. Save both measurements with their positions and sweep settings. Apple on deconvolution
Export what you actually heard
In REW’s File menu, choose Export impulse response as WAV, select the measured IR and its native sample rate, and choose a format your convolution plug-in accepts. Set the export timing so the direct arrival is near the beginning with its attack intact. Use REW’s window or time-zero placement controls and inspect the exported waveform. The default unwindowed export can put the peak a second into the file. Preserve the tail long enough to hear the last reflection and save the unedited measurement separately. REW’s IR export options
Audition the clap and sweep versions fully wet at comparable loudness using the same dry rimshot, then a spoken line. Listen for the first reflection, intelligibility between words and a smooth decay. A single clunk appearing in only one sweep suggests someone moved or a door closed. Repeat before treating it as a room feature. If you hear an unexplained one-second pause, inspect the WAV lead-in before changing the reverb’s pre-delay. Save the preferred WAV, both measurements, the clap original and the room sketch. Name the source and receiver positions in the preset so another engineer can recreate the perspective.
Related reading
- Find the recording spot and the listening spot
- Record room tone and repair a spoken song introduction
- Handbook contents and glossary