How to Sidechain Kick and Bass in Logic Pro

Sidechaining lets one signal control how a processor reacts to another. In a kick-and-bass mix, the kick can trigger a compressor on the bass, briefly lowering the bass when the kick hits. The kick itself is not compressed by that bass compressor. Sidechains also appear in gates and other processors; they are a control path, not a type of compression.

Set up the signal path

  1. Create separate kick and bass tracks. Balance them before adding processing: sidechain compression cannot fix every arrangement or tuning conflict.
  2. Insert Logic's Compressor on the bass channel strip. Choose the kick as the external source in the plug-in's Side Chain menu. If your kick is inside a multichannel drum instrument, route it to its own output or a dedicated bus first.
  3. Play a passage with both parts. Lower the threshold until the gain-reduction meter responds when the kick hits. If it responds to the bass instead, check that you selected the external source.
  4. Start with moderate compression. A ratio around 4:1, a short attack and a release around 100–200 ms are useful audition settings, not a preset for every song. Adjust the threshold for a few decibels of reduction.
  5. Bypass the compressor and compare at similar perceived volume. Keep the change only if the kick reads more clearly and the bass still supports the song.

Adjust it by listening

Attack determines how quickly the bass ducks. Very fast settings can click or distort sustained low notes; lengthen the attack if that happens. Release determines how the bass returns. If the bass stays quiet between kicks, shorten it. If the level flutters or sounds rough, lengthen it. For obvious pumping, make the return part of the groove; for transparent separation, use less reduction.

The sidechain filter changes what the detector hears. It does not EQ the bass output. Use it when a busy drum signal triggers reduction on sounds you did not intend, or separate the kick to make the trigger predictable.

When nothing happens

Check that the trigger track actually produces a signal, that its bus routing is correct, and that the threshold is low enough. Muting or soloing tracks can change routing behavior, so test with the whole session playing. If you use a silent trigger, route it so the detector receives it without sending it to the audible mix.

If every kick seems to remove the entire bass line, reduce the ratio or raise the threshold. You may need a shorter kick, a different bass note length, or arrangement changes instead of more compression. Menu labels vary by Logic version; use the Compressor's external sidechain selector rather than relying on an old screenshot.

Use the snare-only beat to catch a false trigger

Filter the detector key A kick drum sits in front of a detector display whose low-pass curve falls toward high frequencies.
A filter on the detector changes which hits trigger gain reduction. Listen to the key before judging the bass.
Let the kick key the bass compressor The full drum loop feeds the compressor detector while the bass alone travels through the compressor’s audio path. Apply a low-pass filter to the drum-loop key. Return from detector audition to normal listening and match the kick’s gain reduction between passes. Compare the snare-only beat next. If the floor tom still ducks the bass, try an isolated kick key or draw the intended dips.Controls gainDrum-loop keyKick, snare and hatsDetector filterAudition low-passCompressor detectorTriggers gain reductionBass audioSustained noteBass compressorAudio pathMatch kick reductionCompare snare-only beats
Apply a low-pass filter to the drum-loop key. Return from detector audition to normal listening and match the kick’s gain reduction between passes. Compare the snare-only beat next. If the floor tom still ducks the bass, try an isolated kick key or draw the intended dips.
Enlarge diagram
Let the kick key the bass compressor The full drum loop feeds the compressor detector while the bass alone travels through the compressor’s audio path. Apply a low-pass filter to the drum-loop key. Return from detector audition to normal listening and match the kick’s gain reduction between passes. Compare the snare-only beat next. If the floor tom still ducks the bass, try an isolated kick key or draw the intended dips.Controls gainDrum-loop keyKick, snare and hatsDetector filterAudition low-passCompressor detectorTriggers gain reductionBass audioSustained noteBass compressorAudio pathMatch kick reductionCompare snare-only beats

Make a two-bar drum loop with kicks on beats one and three, a bright snare on two and four, and eighth-note hats. Hold a bass note through both bars. This time choose the whole drum loop as the external sidechain for Logic’s Compressor on the bass. Imagine this is the only drum recording you received. The test is whether you can make the bass duck on the kick while leaving it steady under the snare.

First, turn the detector filter off. Set the threshold so the main kicks move the reduction meter, and listen through the snare-only beats. Mark which events also move the meter. Open the Side Chain controls and engage Listen briefly at a comfortable level. Hearing the snare in this mode tells you it reaches the detector. Whether it causes unwanted reduction depends on how it compares with the threshold. Apple’s Compressor sidechain controls

Select the low-pass filter. Start with the cutoff high enough that the snare is still recognizable, then lower it while listening for the body of the kick. Switch out of Listen, leave the filter active and compare the reduction on beats one and two. Filtering changes the level reaching the detector, so check the threshold again. Aim for a similar response on the main kick in the filtered and unfiltered passes. Then compare the snare-only beats at those matched kick responses. A filter that simply stops all gain reduction has failed the test.

Add a floor tom on the last upbeat of bar two. If it makes the bass dip again, audition it through the filtered detector. The tom and kick may occupy much of the same frequency range. Try the clean kick source if you have it. If all you have is this stereo loop, draw a local bass-volume dip on the intended beats and audition it against the filtered version. Keep the method that preserves the bass pickup into the next bar. Write down which events triggered each pass. Those four beat positions make a more useful recall note than a cutoff value copied to every song.

Find out why a parallel drum bus sounds hollow · Bedroom to Stage handbook

Sources and further reading

Related guides

Check whether a ghost kick is ducking the wrong notes

Loop two bars containing a sustained bass note, a main kick and a quieter kick pickup. Put Logic Compressor on the bass and audition its sidechain with the Listen control where available. You should hear the trigger you intended. Switch Listen off before judging the mix. Watch the gain reduction at the pickup. If the bass loses its entrance there, mute just that pickup on a duplicate kick track and select the duplicate as the trigger. Keep the original kick audible in the mix and route the duplicate only to the detector. Compare both versions under the melody. You can keep the full kick performance while choosing exactly which hits open a pocket in the bass. Apple’s Compressor sidechain controls

Back to blog

6 comments

xvLansqNZgpGXTKk

duyEahBpPsHTWXAl

ACLwmlEU

evkKDzUG

AqLxPBrgRI

XxguaZOrY

MuboRCfDXUHZxsK

URDKxkVTOygNCI

UFEhNjQIs

FaNljJGT

Leave a comment