There are two seconds after the final chord when you can still hear the piano strings. Put that detail in the mastering notes. A master is the approved recording prepared for a particular release. Decisions about tone, dynamics, spacing and file format all come back to what a listener should hear from the first sound through those last two seconds.
Start with a listening pass
Import the approved stereo mix at its native sample rate into a fresh session. Disable automatic time stretching and normalization. Confirm the filename against the mix approval, then play the whole song. Note times for anything that draws your attention. If a single harmony syllable protrudes while the rest of the chorus sounds right, ask for a mix revision. An equalizer on the stereo file would change everything playing at that moment.
For an EP, line the songs up in order and listen to each transition without touching the monitor volume. A deliberately quiet opener can lead into a full band. Judge whether the entry feels convincing, how long the silence lasts, and whether the loudest song leaves the later songs anywhere to go. Turn a reference recording down to compare tone and density at roughly matched loudness.
Read two measurements
Integrated loudness, expressed in LUFS, describes a weighted measurement over the program. Reset the meter and play or analyze the entire file. True peak, expressed in dBTP, estimates the highest reconstructed signal level, including peaks between digital samples. A sample-peak meter alone can miss those. Neither reading specifies the sound pressure at your ears. That also depends on your playback equipment, volume and distance. ITU’s loudness and true-peak algorithms
For an exercise, suppose a complete pass measures −16 LUFS integrated and −3 dBTP. Add 1 dB of gain with no other processing. Expect roughly −15 LUFS and −2 dBTP. Now drive a limiter harder and listen to the snare, the singer’s S sounds and the low notes under them. Match the listening levels of the two versions. If you hear the room breathe in time with the kick or the snare lose its attack, ease the limiting or revisit the mix. Write down which version you prefer and why.
Spotify describes −14 LUFS as its normal playback setting. Its mastering guidance recommends true peaks below −1 dBTP, or below −2 dBTP for tracks mastered louder than −14 LUFS. Devices and playback settings differ. Use the service’s guidance alongside the musical decision and the specifications supplied by your distributor. Spotify’s loudness guidance
Make the requested files
Write a delivery sheet before you export. Record the recipient, version name, channel layout, sample rate, bit depth and accepted file type. For example, a distributor accepts stereo PCM WAV at the native 48 kHz and 24-bit resolution of your approved master. Export that version, use a descriptive filename such as GlassWindow_Main_v03_48k24.wav, and keep the editable mastering session. If a second recipient requests 44.1 kHz, 16-bit audio, render separately from the high-resolution source. For a final reduction to 16-bit integer, apply dither once after other processing. Dither uses low-level noise to reduce quantization distortion. Check whether the exporter is already applying it. Ableton’s export and dither settings · Spotify’s native-master delivery guidance
Approve the file that will actually travel
- Open the exported file in a separate player or clean session. Confirm its name, format, channels, duration and measured true peak. Listen from beginning to end with notifications silenced.
- Check the opening pickup, quietest passage, loudest chorus and complete tail. If the tail vanishes during export, extend the render range and repeat the check. If the file has a click track, trace its routing and export again.
- Play the main and instrumental versions at the same timestamp if both were commissioned. Confirm the correct version has the lead vocal, and that effects returns in the instrumental have no stray lead words.
- Give the listener approving the release the exact filenames. File their dated approval and copy those renders to the delivery folder. Reopen a delivered copy and compare its checksum with your approved local file when possible. Matching checksums confirm identical bytes. The listening pass is what confirms the music.
For a closer look, see the Twin Studios guide to audio file formats.
Bedroom to Stage contents · Previous: Mix a song around the part the listener follows · Next: Release a song and keep its paperwork playable
Practice lab · Find the difference between two stem exports
Practice lab · Listen to the master after lossy encoding
Practice lab · Deliver an instrumental and a clean edit from the same mix